By software Solutions

07/28/2021 Hp 3630 printer setupA new 123 hp DeskJet 3630 printer needs a correct setup before it can execute a print command. There are multiple ways to attach the hp printer to your computer. you'll choose the wired USB connection or the wireless connection. But before you connect your printer, you initially need to install the Hp 3630 printer driver and software on your computer. So you see its quite little bit of work to line up a printer, that's why we've compiled this post with step by step instructions for the 123 hp 3630 printer setup. Just follow and execute them within the same order as mentioned and by the time you'll reach the top of this post your printer are going to be properly configured, connected and prepared to print.
Initial setup for 123 Hp 3630 printer

• Remove the hp 3630 from the box; remove all the security tape from the printer and discard it. Place the Hp printer near the pc and make sure that , it's on a flat surface.
  
• Connect the power cable to the rear of the Hp DeskJet 3630 printer and therefore the other end of it to the power supply.
  
• Turn on the printer by pressing the facility button. wait for the power button to prevent flashing and be stable then continue with the installation.
  
• The printer will create some noise, don't be concerned . it is the printer's hardware adjusting and fixing .
  
• Now it is time to insert the ink cartridges in their respective place.
  
• Remove the ink cartridges that are included with the printer from the box. Carefully pull the tape off the rear of the ink cartridges also as from the contact point.
  
• Open the cupboard of the Hp beat one inkjet 3630, the cartridge clip automatically moves to the middle of the unit for cartridge installation.
  
• Insert the ink cartridges into the acceptable slots and push firmly into place.
  
• When the cartridge fits into place, close the printer cover.
  
• The printer will detect the newly installed ink cartridges. the facility button may flash for a few time. await it to prevent flashing before continuing.
  

Install the drivers for the 123 Hp inkjet 3630 printer

• Insert the hp 3630 installation CD into your computer's CD drive . The installer starts automatically. Follow the instructions on the screen to start out installing the DeskJet drivers.
  
• When the printer's software prompt to attach the printer, connect the supplied USB cable to the rear of the printer and insert the other end of the USB cable to your computer's USB port. Allow the pc to detect and connect the printer.
  
• If you do not have the installation CD, first disconnect the USB cable from the printer then open the URL 123.hp.com/dj3630 in your browser.
  
• Download the Hp printer's drivers. When the download finishes run the installer and follow the instructions to put in the drivers.
  
• Now connect the USB cable. After the successful connection, your printer are going to be able to print.
  

123 hp 3630 DeskJet printer setup for wireless connection

• Hp printer wireless connection frees you from the need of placing the printer on the brink of your computer and frees up your working space.
  
• It also gives you the choice to attach the printer with different devices. Hp offers a couple of methods to attach a wireless printer.
  
• These methods depend first on the printer's model then on your choice of how you would like your printer to attach over a wireless network.
  
• We have described the WPS method, as it's supported by most of the available Hp printer models and is that the least complicated one.
  

WPS setup for hp DeskJet 3630

• WPS, an acronym for "Wi-Fi Protected Setup", may be a standard connection method for wireless devices with the router or access point, which allows the printer’s connection to be simple and fast.
  
• Before you employ this method, confirm that your router must be equipped with the acceptable WPS button, a button that the device will presumably have if it's of the newest model.
  
• Secondly, the network must be found out consistent with the WPA or WPA2 security protocol. If the protocol selected for the password was WEP, connecting the printer to the router wouldn't be possible.
  
• After you've got ensured that your router meets all the wants proceed for the WPS connection.
  
• Once the printer is turned on, press and hold the Wi-Fi button on the printer for a couple of seconds until the ON LED starts flashing.
  
• Now on you've got about two minutes to press the WPS button on your router which can enable the WPS feature.
  
• Your printer is now ready for the wireless connection. it'll search the network and connect with it.
  
• After the connection is complete, the Wi-Fi LED will stop flashing and can become stable.
  
• The only thing left is to undertake to launch a printout to verify that the connection has been successful
  

123 Hp 3630 setup for android device

• Anyone who has an Android mobile device since version 4.4 only must download the HP Print Service plug-in
  
• Just download the Hp Print service plug-in from Google Play and install it on your android device to be ready to take full advantage of it.
  
• After connecting the phone on an equivalent Wi-Fi network because the printer, you would like to open the photo or document you plan to print.
  
• Click on the print option then select the HP printer to attach to and press the Update button.
  
• You will have your photos or documents printed in no time.
  

123 Hp DeskJet 3630 setup for iPhone

• Those who shall print anything from a tool belonging to the Apple brand on an HP printer can roll in the hay very easily because of the presence of the AirPrint service.
  
• If you own an iPhone or an iPad you want to first connect the printer to an equivalent Wi-Fi network as that of your phone.
  
• Then you only got to open the document to be printed and continue the Share button.
  
• At now , you would like to travel to the icon concerning printing, select the printer and tap on the print choice to perform the operation .